Concrete Testing Lab Equipments

Approx. Rs 75,000 / PieceGet Latest Price

Product BrochureProduct Details:

Digital Compression Testing Machine with Single Gauge also AvailableThe Digital Compression Testing Machine has been designed to meet the need for a simple,economic and reliable means to test concrete for its compressive strength. The DigitalIndicator incorporates a 4-Digits display calibrated in Kilo Newton (KN) and preset tomaximum load capacity fitted with micro switches to switch-off the motor when the loadapproaches the maximum capacity of the gauge, avoiding any over loading. Relays areincorporated so that the motor does not restart on its own after a power breakdown. Theelectrically operated pumping units are provided with a control knob to adjust the pace ratewhich can be effectively controlled by an experienced operator during the course of testing,by observing the progress of the Digital Indicator readings.

Approx. Rs 10,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
The concrete test hammer is an instrument which is easy to use, for quick and approximatemeasurement of the resistance to pressure of manufactured concrete products. The principleson which it works are based on the rebound impact of a hammer on a piston which restsagainst the surface of the concrete products. The Greater the resistance of the concrete,greater is the rebounded impact. By reading this rebound impact on a scale and relating it tocurves on graphs supplied with the instrument, the resistance to compression in MPA or PSIcan be found, with 20% of actual. Specifications : Consists of a barrel in which is housed ahammer mass attached to an impact spring which slides on a guide bar. A plunger is attachedto the guide bar which is pressed against the surface to be tested. As the piston is pressedagainst the surface to be tested, on reaching the compressive strength, the hammer mass isreleased and rebounds to a certain extent (according to the strength of the surface) which isindicated by a rider on a calibrated scale. A lock button fixed on the body of the hammerlocks the rider in place and the rider can be reached to zero position by using the same button.The equivalent compressive strength can be computed from the chart supplied. Each hammeris calibrated against at standard test hammer, and is suitable for specimen of compressivestrengths 100 - 700 kg/cm. The instrument, complete with a grinding stone for polishing thetest surface, is supplied in carrying case.

Approx. Rs 4,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
As Per IS 269, 712, 5514, 1727, 2645, 6932 (PART IX) BS 6463 It is used for thedetermination of soundness by expansion method of ordinary and rapid hardening Portlandcement, low heat Portland cement and class 'A' Limes. Specification : It consists of a smallsplit cylinder forming a mould. On either side of the split cylinder. Two parallel indicatingarms with pointed ends are attached. Supplied complete with two glass plates and a leadweight.

Approx. Rs 85,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
The Concrete Mixer has been designed for mixing small quantities of concrete used inpreparation of concrete cubes, for testing in laboratories. The purpose of the mixer is tosmear mechanically the aggregate surface with cement paste uniformly & produce a mix ofuniform consistency. This in turn gives consistent quality of cube specimens when casted inthe moulds. The Concrete Mixer developed is transportable on wheels. The design of mixingpaddles ensure uniform & efficient mixing of cement & aggregate both in dry & wetconditions. This machine is suitable for aggregate size upto 20mm. The equipment can alsobe put to use for mixing of any other material in dry / wet conditions. The arrangement helpsthe operators to access the pan contents conveniently & emptying the mixture aftercompletion of the operation. The drum is driven off the ribbed base. The lid with mixingpaddles clears off the top of the drum to provide maximum access to the operator.Specifications: Mixing Capacity : 40 ltrs.,Overall Dimension : 910mm X 875 mm X 1250mm, Motor : 2 HP, 960 RPM

Approx. Rs 15,000 / PieceGet Latest Price

Product BrochureProduct Details:

This is for determining the lateral extension of 15cm dia x 30 cm high cement concretecylinders while testing them under compression. Specification : The unit consists of twomovable frames pivoted at one end. The extensometer is fixed to the specimen with the helpof tightening screws. The lateral extension is indicated on a dial gauge of 0.002mm x 5mm

Approx. Rs 25,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
As Per IS 1199 & BS EN 12350. The instrument is used for work ability as well asconsistency of fresh concrete. A slump Cone and a graduated rod supplied with theinstrument helps the operator to find out slump values and vibration table with container andacrylic disc is used to find out work ability of concrete expressed in Vee Bee degrees, whichis defined as the time in seconds to complete required vibrating at which the fresh concreteflows out sufficiently to come in contract of the entire face of acrylic disc. Specification :The equipment consists of : A vibrating table size 380mm long and 260mm wide, restingupon elastic support at a height of about 305mm above the floor, complete with Start/Stopswitch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescopedwith funnel and guide swivel arm is also detachable from the vibrating table. The divisionsof scale on the rod record the slump of the concrete in millimeters. Supplied complete witha sheet metal container with lifting handles which can easily be fixed to the vibrating table.A slump cone open at both ends with lifting handles and a tamping rod of size 16mm dia and600mm long rounded at both ends.

Approx. Rs 35,000 / PieceGet Latest Price

Product BrochureProduct Details:

As Per IS 11262-1985, ASTM C 186 This equipment is required to determine the heat ofhydration of cement as expressed in calories per gram. The equipment comprises of thefollowing :1) A wide mounted double walled vacuum flask with a stop cock 38 mm & ainsulating container for the flask 2) A Beckman thermometer (Range 5° C )held tightly bythe cock stopper in such a way as to avoid accidental contact with the stirrer blade & thereading lens. To facilitate the easy removal the cock stopper is in two halves.3) A constantspeed stirrer (double bladed propeller type) extended to within 38 mm from the bottom ofthe flask.4) A funnel (Gooch type)with a stem of 6 mm inner dia & a body approx. 25 mmlong and 25 mm dia. is fitted to the cock stopper for introducing the sample All the above tocombine to form the calorimeter for the determination of heat of hydration of cement.Suitable To Operate on 230 V A.C. 50 Hz

Approx. Rs 17,500 / PieceGet Latest Price

Product BrochureProduct Details:

We are providers of Vibratory Hammers, which is a specialized equipment used consistentlyat construction sites. The Vibratory Hammer is electrically operated. Our Vibratory Hammerhas several uses. Some of them are listed below. Specifications Used for changing the soilformation with the use of its vibration Used for driving hammers into heavy or hard pilesUsed for the compaction of concrete cubes of 150mm & 100mm

Approx. Rs 500 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
The product is available as per the customer requirement. Our product is highly appreciated by customers. 

Approx. Rs 85,000 / PieceGet Latest Price

Product BrochureProduct Details:

Specification: The Laboratory Concrete Mixer is used for preparing Mix Design of Concrete.It consists of a steel vessel of 55/ 110 Litres capacity, mounted on a frame. The vessel isrotated at 20-22 RPM with the help of a motor and a pulley arrangement. The vessel oflaboratory concrete mixer can be titled to any angle by a hand wheel and counter weight.This facilitates mixing and discharge. Blades are provided inside the vessel to mix thematerial thoroughly. The large pulley wheel facilitates manual rotation of the drum duringpower failure. The drum, pulley wheel, and motor are mounted on a steel frame in theselaboratory concrete mixer. The concrete mixer is fitted with 1⁄2 HP motor. Suitable forOperation on 220V, Single Phase, 50Hz, AC Supply.

Approx. Rs 40,000 / PieceGet Latest Price

Product BrochureProduct Details:

Curing Tank
24 Hour cycle from time of mixing. - Controlled 35oC or 100oC ±2oC Curing Temperature for concrete. - Controlled 27oC ± 2oC Curing Temperature for grey cement. The tank has been designed to accommodate 150mm/70.6mm cube moulds upto 36/72 cube mould and fully insulated, complete with a hinged lid, heater, thermostat and re-circulated pump. Provision of two removable racks allowing free circulation of water around each mould. The pump, drain valves and electrical equipment are housed in a compartment located at one end of the tank. The Tank is heated by a immersion heater under normal conditions and refrigeration system for grey cement the temperature is controlled at 35oC or 100oC ± 2oC / 27oC 2oC , expect for the 15 minutes after immersion of the freshly made specimens.
Salient Features

• Curing Tank for 6/12 moulds of 150mm / 70.6mm size
• Curing Tank for 12/24 moulds of 150mm / 70.6mm size

Taag: Curing Tank Manufacture in Chennai

Curing Tank Manufacture in Tamilnadu, Curing Tank Manufacture in Chennai, Curing Tank Manufacture in Kanchipuram, Curing Tank Manufacture in Tiruvallur, Curing Tank Manufacture in Cuddalore, Curing Tank Manufacture in Villupuram, Curing Tank Manufacture in Vellore, Curing Tank Manufacture in Tiruvannamalai, Curing Tank Manufacture in Salem, Curing Tank Manufacture in Namakkal, Curing Tank Manufacture in Dharmapuri, Curing Tank Manufacture in Erode, Curing Tank Manufacture in Coimbatore, Curing Tank Manufacture in The Nilgiris, Curing Tank Manufacture in Thanjavur, Curing Tank Manufacture in Nagapattinam, Curing Tank Manufacture in Tiruvarur, Curing Tank Manufacture in Tiruchirappalli, Curing Tank Manufacture in Karur, Curing Tank Manufacture in Perambalur, Curing Tank Manufacture in Pudukkottai, Curing Tank Manufacture in Madurai, Curing Tank Manufacture in Theni, Curing Tank Manufacture in Dindigul, Curing Tank Manufacture in Ramanathapuram, Curing Tank Manufacture in Virudhunagar, Curing Tank Manufacture in Sivagangai, Curing Tank Manufacture in Tirunelveli, Curing Tank Manufacture in Thoothukkudi, Curing Tank Manufacture in Kanniyakumari, Curing Tank Manufacture in Krishnagiri, Curing Tank Manufacture in Ariyalur, Curing Tank Manufacture in Tiruppur

Approx. Rs 40,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
Electrical cum Hand Operated also AvailableThe Flexure Strength Testing Machines are designed to provide maximum rigiditythroughout their working range. The load is applied by the upward movement of a hydraulicram. The jack can be raised or lowered for testing different size beams. The load is indicatedon a calibrated Bourdon tube type Pressure Gauge of range: 0-100kN x 0.5kN (0-10,000 kgfx 50 Kgf). The load gauge is calibrated against NPL/ NCCBM certified proving ring.

Approx. Rs 25,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
As Per IS 1199 1959 & BS 1881-106 As entrainment of air in limited percentage improvesdurability of concrete and very low percentages deteriorate it ,measurement of air entrappedin freshly mixed concrete becomes important. The use of chemical additives to increase workability of concrete in turn requires an air content check to be made. Air entrainment metersare used to determine air entrained in freshly mixed concrete by pressure method.Specification : The apparatus consists of a pressure tight flanged cylindrical measuring bowlof 0.005 cubic meter capacity for maximum size of aggregate 38mm. The bowl is fitted witha removable flanged conical cover assembly with the help of a seal. The conical cover hasan air valve and a petcock for bleeding off the water. A transparent cylindrical stand pipewhich is graduated in air content is fixed to the conical cover assembly. Pressure is appliedto the specimen with the help of a pressure bulb and the pressure is recorded on the pressuregauge which is mounted on the stand pipe. The whole assembly is mounted on a flat base.The instrument is supplied complete with one each following accessories. Other Size arealso available. 0.007 cubic meter capacity for maximum size of aggregates 38mm, 0.01cubicmeter capacity for maximum size of aggregate 75mm. 0.1 cubic meter capacity for maximumsize of aggregate 150mm.

Approx. Rs 7,500 / PieceGet Latest Price

Product BrochureProduct Details:

25kgf to 100kgf (1KN) 200kgf (2KN) 250kgf (2.5KN) 1000kgf (10KN) 2000kgf(20KN) 2500kgf (25KN) 3000kgf (30KN) 5000kgf (50KN) 100KN (10Tons) 200KN(20Tons) 500KN (50Tons) 1000KN (100Tons) 2000KN (200Tons)Specification: The Proving Rings are made of special steel, carefully forged to provide highand stable accuracy, dependability and repeatability. The dial gauge and anvil are mountedon U-brackets clamped to the ring body by set screws. The indicator has a sensitivity of0.002mm/ div and the deflection is directly proportional to the applied load. The rings aresupplied complete with dial gauge and Works Calibration Chart, individually packed inpolished wooden boxes. NPL (India) / NCCBM Calibration Certificates can also be arrangedfor any proving ring at an additional cost. Separate Pair of Loading Pads are provided to suiteach proving ring.

Approx. Rs 15,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
As Per ASTM C-360 The apparatus is used to determine the work ability of Portland cement& concrete. The Kelly ball test is considered to be simple and much faster than the slumptest. Twice the Kelly ball reading approximately equals the slump. It consists of a cylinderwith a ball shaped bottom and handle, together weighing 15 kg. A strip frame, guides thehandle and serves as a reference for measuring the depth of penetration. The handle isgraduated in mm. Penetration can be recorded to the nearest 0.5mm.

Approx. Rs 2,100 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
As Per IS 269, 712, 5514, 1727, 2645, 6932 (PART IX) BS 6463 It is used for thedetermination of soundness by expansion method of ordinary and rapid hardening Portlandcement, low heat Portland cement and class 'A' Limes. Specification : It consists of a smallsplit cylinder forming a mould. On either side of the split cylinder. Two parallel indicatingarms with pointed ends are attached. Supplied complete with two glass plates and a leadweight.

Approx. Rs 5,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
The product is available as per the customer requirement. Our product is highly appreciated by customers. 

Approx. Rs 75,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
The product is available as per the customer requirement. Our product is highly appreciated by customers. 

Approx. Rs 14,000 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
The product is available as per the customer requirement. Our product is highly appreciated by customers. 

Approx. Rs 2,300 / PieceGet Latest Price

Product BrochureProduct Details:

Description:
150mm x 150mm x 300mm100mm x 100mm x 200mmMoulds for testing concrete cylinders for Compressive Strength Testing are offered in twodifferent sizes. These cylindrical moulds are made of Cast Iron and split into two partslongitudinally. These are supplied complete with a base plate and top plate

Approx. Rs 1,700 / PieceGet Latest Price

Product BrochureProduct Details:

As Per IS 1199, IS 7320 Specification: The slump cone in these slump test apparatus is filledwith freshly mixed concrete and tamped with a tamping rod in three or four layers. The topof the concrete is leveled off with the top of the slump cone, the cone is lifted vertically upand the slump of the sample is immediately measured. The complete slump test apparatusset comprises of a Steel Octagon Base Plate (8 faces) with carrying handle, GraduatedTamping Rod 16mm dia. x 600mm long with one bullet end, slump cone having base200mm, height 300mm fitted with handle.